เขียนโปรแกรมอ่านค่าอุณหภูมิจาก DS18B20 แสดงผลที่ 7 segment MAX7219
ไลบารี่เพิ่มเติม
-OneWire.h https://github.com/PaulStoffregen/OneWire (https://github.com/PaulStoffregen/OneWire)
-DallasTemperature.h https://github.com/milesburton/Arduino-Temperature-Control-Library (https://github.com/milesburton/Arduino-Temperature-Control-Library)
-LedControl.h https://github.com/wayoda/LedControl/releases (https://github.com/wayoda/LedControl/releases)
*ดูวิธีติดตั้งในงานครั้งที่ 20 (http://www.praphas.com/forum/index.php?topic=266.0)
โจทย์การทดลอง
-เขียนโปรแกรมรับค่าอุณหภูมิที่อ่านจาก DS18B20 แสดงผลที่ 7 segment MAX7219
-โปรแกรมรายละเอียดพิเศษรายกลุ่ม (แจ้งให้ทราบเมื่อถึงชั่วโมงเรียน)
วงจรที่ใช้ในการทดลองสำหรับผู้ที่ใช้บอร์ด Arduino
(http://www.praphas.com/PhotoForum/arduino/Lab-44-01.png)
วงจรที่ใช้ในการทดลองสำหรับผู้ที่ใช้ไอซี ATmega328 (ที่มี Boot Loader Arduino)
(http://www.praphas.com/PhotoForum/arduino/Lab-44-02.png)
ตัวอย่างโปรแกรมอ่านค่าจาก DS18B20
#include <OneWire.h>
#include <DallasTemperature.h>
OneWire oneWire(2); //Connect to Pin 2 (D2)
DallasTemperature sensors(&oneWire);
void setup(void)
{
Serial.begin(9600);
Serial.println("Dallas Temperature IC DS18B20");
sensors.begin();
}
void loop(void)
{
Serial.print(" Requesting temperatures...");
sensors.requestTemperatures(); // Send the command to get temperatures
Serial.println("DONE");
Serial.print("Temperature is: ");
Serial.print(sensors.getTempCByIndex(0));
Serial.println(" Degrees C");
Serial.print("Temperature is: ");
Serial.print(sensors.getTempFByIndex(0));
Serial.println(" Degrees F");
}
ตัวอย่างโปรแกรมแสดงผล 7 Segment MAX7219
#include "LedControl.h"
LedControl lc=LedControl(6,4,5,1); // Pin 11->DIN, 13->CLK, 12->CS, 1 = No.of devices
void setup()
{
lc.shutdown(0,false); // Enable display
lc.setIntensity(0,10); // Set brightness level (0 is min, 15 is max)
lc.clearDisplay(0); // Clear display register
}
void loop()
{
lc.setDigit(0,7,2,false);
lc.setDigit(0,6,3,true);
lc.setDigit(0,5,4,false);
lc.setRow(0,4,B00110111);
lc.setRow(0,3,B01001111);
lc.setRow(0,2,B00001110);
lc.setRow(0,1,B00001110);
lc.setRow(0,0,B01111110);
delay(1000);
}